DIY Outdoor String Lights

Step 1

Using an awl, puncture the conduit about three inches from the top to make drilling easier. Of course, you could make the hooks higher or lower, but three inches looked about right.

1 / 13

Step 2

Image Source: Bright July

Spray paint! We used Rust-Oleum in dark bronze. We used all of one can and just a tiny bit of a second can. (For some reason, I missed taking a picture of spray-painting the conduit itself — but you get the idea.) We painted the conduit, hooks, and caps separately. An old edging tie worked well to help me get all the sides of the hooks evenly painted. (As a bonus, you get a nice view of my favorite painting shirt!) Then after it was assembled, I gave it one final sweep to cover the head of the screw.

2 / 13

Image Source: Bright July

3 / 13

Step 3

Image Source: Bright July

Cut lengths of plastic electrical conduit to a length of a minimum of 18 inches and ideally 24 inches. Our deck is on a slant, so it's higher on one side than the other. So each piece of piping was a different length between those two measurements. The piece of pipe we bought was one inch in diameter. The conduit was 3/4 of an inch, so it was a perfect fit.

4 / 13

Step 4

Image Source: Bright July

Attach the pipe straps (hooks). You can use a screwdriver or a drill for this. Jeremy started the screws with a screwdriver and then drilled them in.

5 / 13

Image Source: Bright July

6 / 13

Step 5

Image Source: Bright July

Attach the caps. We bought 1/2-inch "Knock Out Seals" for this. They are essentially flat caps with metal ribbing on the inside that securely seals it at the end of the pipe. I'm sure they have a precise and specific purpose that probably has nothing to do with what we used it for, but it worked perfectly! We just needed to use pliers to adjust the angle of the metal ribbing inside so it fit well.

7 / 13

Step 6

Image Source: Bright July

Bury the pipes. I wish I could say the process of burying the pipes in the ground was precise and exact, but that is so not our style! We completely lucked out with the depth of the pipe. We were quite shocked when the poles all measured the same height in the end (actually they are about 1/2 inch off from each other, which is too small to detect with the eye — good enough for us!). Being that our deck is built on slanted ground, this was a major win. Also, I spray-painted the part of the pipe that is visible above ground after the fact, but didn't take a photo of it. Only one needed to be painted, as the other two are completely concealed by plants. About six inches of pipe sticks up out of the ground.

8 / 13

Step 7

Image Source: Bright July

Insert poles into their fittings, and attach extra pipe straps to the exterior wall where the lights will hang.

9 / 13

Step 8

Image Source: Bright July

Drape lights from your poles, and you are done!

10 / 13

Image Source: Bright July

11 / 13

Image Source: Bright July

This project was so rewarding. The lights cast a warm, flattering glow that will be perfect for entertaining. I also love that we can take them down easily by lifting the poles out of the ground and unhooking the lights. Easy!

You should do it.

Here's the cost breakdown:

Three 10-foot-long pieces of electrical conduit, 3/4 inch in diameter: $3.98 each — $11.94
One 10-foot-long piece of plastic piping (it was in the same aisle as the conduit, so I'm assuming it also has an electrical function) — $2.92
Two packages of single anchor pipe straps, 3/4 inch diameter — 98 cents each — $1.96
One package of 1/2-inch "Knock Out Seals" — $1.30
Two cans of Rust-Oleum Hammered Dark Bronze Spray Paint — $5.98 each for a total of $11.96

Total: $30.08!

The string lights are from Target and cost $12.95 for each 20-foot strand. Our deck is 10 by 20 feet, so we needed two strands.

This brings the final total for this project to $55.98! Not bad considering the many more expensive alternatives out there. I'm in love.

12 / 13

Image Source: Bright July

13 / 13